Toyota Maintenance on 4x4Wire

Toyota Maintenance: Replacing Alternator Brushes


Welcome to 4x4Wire! You, your 4x4, and Access... Short Cuts
More on 4x4Wire: 4x4 Tech | 4x4 Reviews | Destinations | 4x4 Access
More 4x4 Tech 4x4Wire: Jeep Tech | Jeep Projects | Jeep News | Jeep Reviews | Jeep Gallery
Toyota FAQ | Toyota Projects | Toyota Maintenance | Toyota 4Runner | Toyota Tech | Hot Toy | Insider
Mitsubishi on 4x4Wire | Mitsubishi Projects | Mitsubishi Reviews | Mitsubishi Tech
Intro | Isuzu News | Isuzu Tech | Isuzu Events | 4x4Wire Gallery


Author: Adam Fertig - 10/2003

If you have a early model Toyota 4Runner or pickup and the charge and brake lights on the dash light up at the same time, there is a good chance that your alternator will soon need replacement. This is exactly what happened to me. The brake light first came on for a day or two. I checked all of the brake components and could find no problems. Then all of the sudden the charge light and brake light lit up at the same time. This was puzzling since the battery read 13 volts while running. After a few days I encountered a major problem. On my way home from work, the CD player quit working, and my dash lights went dim. I looked at the volt meter in the dash, which was at the half way point. I began to put the turn signal on to get into the other lane, and the voltage dropped below half. Next the motor cut out, and the headlights went dim. This was a sure sign of a bad alternator. Had the battery been the culprit, the problem would not have been likely surface while the vehicle was running.


Fortunately there is a low cost alternative to a new alternator. All that is likely to be needed is a new set of alternator brushes for $10-$20! You can find these brushes at most major auto parts stores, or directly from the dealer using part number 27370-35060. The part from Toyota is a complete brush set, including the bracket that holds the brushes. The parts store piece consists of only the two metal brushes, with a long wire attached to each. The brushes have copper leads attached to them that runs though the middle of a spring, and then goes out the back of the brush holder, and is soldered in place. The Toyota part requires no soldering, as it is a drop in unit. The parts store piece requires removing the old brushes, routing the copper wire though the spring and out the back of the holder, and soldering it back into place. Save yourself the trouble and order the Toyota part as soon as your charge light comes on. Retail is $17 for the genuine Toyota part and $9 for the parts store piece.

Tools for the job are as follows.


First thing to do is disconnect the negative battery terminal, then focus in on the alternator.

Distributor and air hoses removed to free up working space.

To make removal of the alternator easier, you will need to get a few things out of the way. Start by removing the spark plug wires and the distributor cap. Mark the plug wires and the distributor cap to aid in reassembly. The distributor cap bolts require an 8 mm socket or a screwdriver to remove. Next remove the two small hoses that connect to the air box, to the right of the radiator. It should look like the picture on the right, but with the alternator still in there.

There are a few wires that need to be removed from the alternator. Start with the wire covered with the 90 degree boot. Grab your 10mm socket and remove the nut that holds the cable on. Right behind this wire is a larger wiring harness that is plugged into the back of the alternator. Remove it by squeezing and pulling away. Now you will have another one wire harness and a plastic clip that is clipped to the alternator body on the underside of the alternator. Unplug the wire, and use a screwdriver to pry off the plastic clip holding the wire onto the alternator.

Now remove the 12 mm lower adjusting bolt. Once it is loosened, it should relieve tension on the belt. Push on the belt to see how tight it is, and remember to tighten it to spec upon reinstallation. Go ahead and remove the belt from the pulley, then remove the upper pivot bolt with a 14 mm socket. The alternator should now be free from the brackets. Snake the alternator out of the engine bay, which should be much easier with the air box hoses out of the way.


Battery terminal mounting hardware removed.

Cover removed from case.

Using a 10 mm socket, remove the nut and plastic boot that hold the positive battery terminal on to the alternator.

Next remove the three 8 mm bolts that affix the back cover to the alternator housing. This will expose the brush holder and the rubber boot.

Two phillips head screws hold the brush holder in place. Be careful to use the right sized screwdriver, as the screws can strip fairly easily. Pull the rubber boot off and inspect the brushes. They should stick out and have a spring effect to them. Mine were short, stubby, and uneven.

Once you get the new brushes in, compress the brushes and remount the holder on the shaft of the alternator, then put the screws back into place. Bolt the cover back on and the boot for the positive terminal that you previously removed. It is suggested that you liberally coat all bolts that thread into the aluminum housing with anti-sieze to prevent them from stripping out. You are ready to put the alternator back in.


Old alternator brushes, ready for replacement.
Applying tension to the alternator belt.

Put the alternator back in place, and loosely attach the upper and lower mounting bolts before slipping the belt back on the pulley. Next, grab a crow bar or a long thick screwdriver, which is used to put tension on the belt. Stick the crow bar between the motor and the alternator and pivot it. Now tighten the lower bolt while keeping pressure on the crowbar.

When you have sufficient tension on the belt, go ahead and tighten up the upper bolt. Put reattach the three wires you removed from the alternator. Reinstalled the distributor cap and the spark plugs wires in the correct position. The final step is to reinstall the two hoses on the air box and the repair is completed.

The new alternator brushes solved my problems with the low voltage, and the related problems with the charge and brake lights. Total repair time was approximately two hours, but this could have been cut in half if the factory Toyota part was used.


Related Links

Trending on 4x4Wire TrailTalk Forums

New Topics on TrailTalk
New 2017 Jeep Wrangler JK Lift Kits from BDS
by 4x4Wire
12/09/16 08:11 PM
Tip for Gen2 Swaybar Endlink Removal
by BlueMont
12/07/16 10:36 PM
2017 BAJA RALLY PRE-SEASON ENTRIES NOW OPEN
by 4x4Wire
12/07/16 06:16 PM
Gen2.5 Locker R&P Upgrade
by BlueMont
12/07/16 04:08 AM
BDS: Air Ride RAM 2500 Gas Trucks 5.5" Lift Kits
by 4x4Wire
12/07/16 12:26 AM
SuperPro Lift Correction Arms for Nissan Patrol GU
by 4x4Wire
12/07/16 12:14 AM
Recent Posts on TrailTalk
New 2017 Jeep Wrangler JK Lift Kits from BDS
by 4x4Wire
12/09/16 08:11 PM
Monty upgrade ideas wanted
by TOASTY
12/09/16 03:50 AM
Tip for Gen2 Swaybar Endlink Removal
by Mudraider
12/09/16 03:11 AM
Gen 2 seats in a Gen 1
by poormansporsche
12/08/16 02:22 AM
2017 BAJA RALLY PRE-SEASON ENTRIES NOW OPEN
by 4x4Wire
12/07/16 06:16 PM
Engine build sanity check (and a sob story)
by Mudraider
12/07/16 05:30 PM
Gen2.5 Locker R&P Upgrade
by BlueMont
12/07/16 05:01 AM

OutdoorWire Websites

OutdoorWire

OutdoorWire

Portal page for OutdoorWire Access and Landuse Central Read More
4x4Voice

4x4Voice

California off road recreation news and information Read More
MUIRNet News

MUIRNet News

News and information about issues affecting outdoor recreation Read More
4x4Wire

4x4Wire

Off road recreation and 4x4 Technical news and information Read More
TrailTalk

TrailTalk

4x4Wire TrailTalk Forums for a variety of 4x4 tech information Read More

4x4Wire Tech Section

Jeep 4x4 Tech

Jeep 4x4 Tech

Jeep Tech from JeepWire Read More
Toyota 4x4 Tech

Toyota 4x4 Tech

Toyota Tech from 4x4Wire Read More
Mitsubishi 4x4 Tech

Mitsubishi 4x4 Tech

Mitsubishi Tech from 4x4Wire Read More
Isuzu 4x4 Tech

Isuzu 4x4 Tech

Isuzu Tech from 4x4Wire Read More
  • 1




OutdoorWire, 4x4Wire, JeepWire, TrailTalk, MUIRNet-News, and 4x4Voice are all trademarks and publications of OutdoorWire, Inc. and MUIRNet Consulting. Copyright (c) 1999-2016 OutdoorWire, Inc and MUIRNet Consulting - All Rights Reserved, no part of this publication may be reproduced in any form without express written permission
You may link freely to this site, but no further use is allowed without the express written permission of the owner of this material.
All corporate trademarks are the property of their respective owners.