4x4Wire

About you, your 4x4 and access
John Stewart

Safety Whip Mounting on a Jeep

Whip Mount in positionThe flags are typically a 5 foot fiberglass pole with a red flag attached to the top and either 1/4” or 5/16” diameter.  While there are a number of different methods to mount the flag on an ATV, dune buggy, or side-by-side, mounting on a full-size 4x4 requires a little planning.

My recent visit to the Sand Sports Super Show provided an interesting, easy to mount quick-release system designed to simplify the process for mounting and dismounting whips with no tools and no trimming of shattered ends necessary.

Continue reading
  6166 Hits
John Stewart

Replace the hook

b2ap3_thumbnail_DSC00108.JPG

It always seems to be in the way and no convenient place to snug it out of the way.  Enter the next generation of decorations for the end of winch cable.

Factor 55 has designed a line of strong and light recovery products for the the off road market based on exacting aerospace and defense industry standards.  Their ProLink series, of 6000 series aluminum, eliminates the traditional winch hook in favor of a safer and stronger screw pin shackle D-Ring.

Continue reading
  8352 Hits
Jon Negaard

Building a General Purpose Mobile Comms Suite

I like to get out with a purpose.  Usually, my rig takes me places where I like to do other things.  I have bikes, kayaks and feet that like to get away from the vehicle more than I tend to take the truck down trails these days.  This is not to say that 4 wheeling is not a goal; time to take advantage of extended outings just hasn't been in abundance.  That said, I decided that I wanted a communication system that would function with a general purpose.  I wanted to use both amateur radio frequencies and CB communications.

Continue reading
  7517 Hits
John Stewart

Airdown Made Simple

Staun Tire Deflator Set okay, I had read about them.  I won a set in a raffle once.  They stayed in the console while I used my favorite home-brew hose connection to air-down two tires at a time.  One morning while reaching for my air gauge, I grabbed the little pouch of deflators.  Well, why not try them?

Continue reading
  8205 Hits
John Stewart

Leveling the Dodge 1500 4x4

Torsion Key Comparision

I found a solution with the ReadyLift Leveling Suspension Kit which advertised maintaining stock height and raising the front end to eliminate the nose down look.

The kit for the Dodge 1500 provided two forged torsion bar keys.  The hex slots were clocked slightly different than the stock keys which provided for the front nose lift.

Installation is simple, requiring that the front end be raised (and supported) enough to loosen and remove the torsion bars.

The kit does include a bracket for unloading the torsion bar pressure.  The heavy metal bracket the slips over the top of the key holder.  Still necessary is a tool to compress the key.  The recommended tool is GM OTC 7822A.

Once the torsion key is unloaded, the torsion adjusting bolt can be removed.  At this point, the torsion bar can be removed from its socket enough to allow the stock key to be remove and replaced with the new torsion key.  

In most cases the torsion bars will loosen and reinstall with no problems.  If the truck has seen any off-road action, gentle persuasion may be required or extra bolts may need to be loosened to provide crossmember movement enough for clearance.

As with any modification to a suspension system, a preliminary inspection of all suspension components (including alignment) is highly recommended.  During the preliminary inspection of the Dodge, the lower ball joints were found to be slightly out of recommended tolerances and the shocks were worn.

Wheel alignment is critical for safe and efficient vehicle operation.  The torsion key replacement changes the geometry of the steering and suspension requiring an alignment.

The torsion bar adjustments require a flat surface and tape measure.  With the truck sitting on a level surface, measure the height from a reference point just behind the front wheels and a reference point just ahead of the rear wheels on each side.

 For a starting point, assume the height on the left rear is the desired height.  Starting with the left torsion adjustment, snug it to the point where the left front is raised to match the left rear height.  Some adjust may be needed on the right to fine tune to make the four height measurements equal.  

Generally, the left torsion adjustment will have the most effect.  This adjustment will make for a stiffer ride and can be tweaked for personal preference.  Each 1/4 inch of adjustment of the bolt equal one inch of height at the wheel.

With the torsion bar set, it is time to replace the worn lower ball joints.  Spicer provides a very durable ball joint and does have one for the Dodge Ram trucks.  While the ball joint does come with a grease zerk fitting, that fitting does need to be removed and replaced with a plug.  The grease zerk fitting will interfere with the IFS/CV joint.  The Spicer part number for the lower ball joints used is: 505-1294.

The final step is an alignment to set the correct camber and caster of the front tires.  This should be accomplished by a certified mechanic with a functional alignment rack and gauges.

With the torsion key, ball joint, and alignment complete, it was time to replace the shocks.  The rear height was not changed so the stock shock length was not altered.  However, the front was raised slightly more than one inch. 

Raising the front meant that stock shocks (10.75 inches collapsed and 15.875 inches extended) would be shorter than required.  Bilstein provides a shock in their 5100 series that is 13.26 inches collapsed and 21.51 inches extended.  While it is slightly longer than necessary, it is a standard item.  Adding 15 inch limiting straps will reduce the downward travel and potential for binding the IFS CV joint.  The Bilstein part numbers used are: rear - F4-BE5-2550-H1 and front - F4-BE5-6528-H6.

And, no major work is complete without a look at the brake pads and rotors.  With the high mileage, a brake job was due.  The front and rear pads were worn as were the front brake rotors.  As the front rotors are the most prone to wear, they are recommended to be replaced rather than machined. However, the rear rotors showed minimal wear and required a minimal machining to clean up the rotor surface and ensure it was smooth.

All work completed, it was time for a road test.  The road test revealed improved steering control and overall ride improvement.  It was like driving a new vehicle.

Work was done by:
Roger Daniels Alignment & Brake
8517 Ablette Road, Shop F
Santee, CA  92071
(619) 562-7969
BAR # ARD214109

 

  16032 Hits
4x4Wire.com

OutdoorWire, 4x4Wire, JeepWire, TrailTalk, MUIRNet-News, and 4x4Voice are all trademarks and publications of OutdoorWire, Inc. and MUIRNet Consulting. Copyright (c) 1999-2019 OutdoorWire, Inc and MUIRNet Consulting - All Rights Reserved, no part of this publication may be reproduced in any form without express written permission. You may link freely to this site, but no further use is allowed without the express written permission of the owner of this material. All corporate trademarks are the property of their respective owners.